[Free] Download New Updated (April 2016) VMware VCPN610 Actual Tests 71-80

Ensurepass

QUESTION 71

What is determined when an NSX Administrator creates a Segment ID Pool?

 

A.

The range of VXLAN Network Identifiers (VNIs) that can be assigned to Logical Switches.

B.

The total number of Logical Switches that can be deployed in a single Compute Cluster.

C.

The range of VLAN segments that can be assigned to Transport Zones.

D.

The total number of addresses that can be used to assign VTEP IP addresses to ESXi hosts during host preparation.

 

Correct Answer: A

 

 

QUESTION 72

Which feature is not supported by the vSphere 5.5 Distributed Switch?

 

A.

Multiple link aggregation groups

B.

Differentiated Service Code Point (DSCP) QOS at layer3

C.

Packet captures at the uplink, virtual switch port, or vNIC

D.

IGMP snooping at layer 2

 

Correct Answer: D

 

 

QUESTION 73

A vSphere administrator deployed an NSX Edge Load Balancer in HA mode. What happens in the event the Load Balancer has a failure?

 

A.

The secondary NSX Edge Load Balancer assumes the role of primary. Existing Flows will need to have their connections reestablished.

B.

HA will start the NSX Edge Load Balancer on another ESXi host in the cluster. All existing flows will need to have their connections reestablished.

C.

HA will start the NSX Edge Load Balancer on another ESXi host in the cluster. The NSX Controller caches existing flows and hands them to the Load Balancer when it is back up.

D.

The secondary NSX Edge Load Balancer assumes the role of primary. The NSX Controller caches existing flows and hands them to the Load Balancer when it is back up.

 

Correct Answer: A

 

 

 

 

 

 

 

 

 

QUESTION 74

An administrator is deploying a distributed router and is adding an interface for a logical switch, as shown in the following exhibit:

 

clip_image002

 

The administrator clicks on the Change link to specify the network to connect to. Selecting the distributed portgroup, the administrator finds that no portgroups are listed. The administrator verifies the desired portgroup exists in vCenter Server. What condition would result in this behavior?

 

A.

The MTU size is set to 1500

B.

A subnet has not been configured

C.

The interface name has an invalid character

D.

The interface type is incorrect

 

Correct Answer: D

 

 

QUESTION 75

What is the most restrictive NSX role that can be used to create and publish security policies and install virtual appliances?

 

A.

Security Administrator

B.

NSX Administrator

C.

Auditor

D.

Enterprise Administrator

 

Correct Answer: D

 

 

QUESTION 76

How many Logical Interfaces can be assigned to a single Distributed Router instance?

 

A.

1

B.

12

C.

1000

D.

1200

 

Correct Answer: C

 

 

QUESTION 77

A company has augmented its Data Center infrastructure by using vCloud Hybrid Service during peak hours. The company wants to extend their existing subnets into the cloud while workloads retain their existing IP addresses. The virtual machines in these subnets use an NSX Edge Gateway as their default gateway. Which solution should this company use?

 

A.

Layer 2 VPN

B.

MPLS VPN

C.

IPSec VPN

D.

SSL VPN

 

Correct Answer: A

 

 

QUESTION 78

Which two are pieces of information required to perform an NSX backup? (Choose two.)

 

A.

Transfer protocol

B.

Default Port

C.

Number of backups retained

D.

Filename prefix

 

Correct Answer: AD

QUESTION 79

Which statement best describes scaling a fault tolerant spine-leaf multipathing fabric architected for an NSX deployment?

 

A.

Scaling should be performed by replacing 1Gbps links in the architecture with 10Gbps links.

B.

Scaling should be performed by increasing the number of links from each leaf switch to the associated spine switches in the architecture.

C.

Scaling should be performed by increasing the number of spine switches while maintaining point-to-point connectivity between leafs and spines.

D.

Scaling should be performed by using layer 2 switching between the leaf and spine switches.

 

Correct Answer: C

 

 

QUESTION 80

You have a vSphere deployment consisting of ESXi 5.1 hosts and a vCenter Server 5.5. You are deploying NSX and begin by creating a vSphere Distributed Switch (vDS) on the vCenter Server using default settings. What is the next step in preparing the deployment for NSX?

 

A.

Use the option Add host networking.

B.

Use the option Add and Manage Hosts.

C.

Deploy NSX on each host.

D.

Upgrade the ESXi hosts.

 

Correct Answer: D

 

Free VCE & PDF File for VMware VCPN610 Real Exam

Instant Access to Free VCE Files: CompTIA | VMware | SAP …
Instant Access to Free PDF Files: CompTIA | VMware | SAP …